Full configuration table — Mass-EXPERT

1A | Nominal diameter

Code	DN	Max. flow rate, kg/min	Max. flow rate, kg/h
001	DN01	0.2	12
002	DN02	1.6	96
003	DN03	3	180
004	DN04	5	300
008	DN08	20	1 200
015	DN15	60	3 600
020	DN20	100	6 000
025	DN25	200	12 000
040	DN40	450	27 000
050	DN50	650	39 000
080	DN80	2 000	120 000
100	DN100	3 000	180 000
150	DN150	12 000	720 000
200	DN200	18 000	1 080 000
250	DN250	29 000	1 740 000

2B | Standard operating conditions

Code	Description	Note
T	Standard version	−50…+150 °C, P≤10 MPa
P	Elevated pressure	−50…+150 °C, >10 MPa; ≤45 MPa depending on size (operation manual, Table 2.1)
L	Cryogenic design	−196…+150 °C, U/Δ models only
D	Ultra-low temperatures	−255…+150 °C, remote design only; below −196 °C, measurement is outside the type approval scope — subject to separate agreement
G	High temperature	−50…+230 °C; remote design — available, with some exceptions (operation manual 2.2.5)
C	Ultra-high temperature	−50…+350 °C, remote design only
X	Special operating conditions	detailed description required

3C | Sensor type

Code	Description	Note
U	U-shaped measuring tube type	for ≥ DN03 only
K	Wide U-shaped measuring tube type	DN02–DN25 only
W	Micro-bend measuring tubes
L	Straight-tube
D	Triangular Δ-type measuring tubes	DN01, DN02, DN25 only
X	Special version	description required

4D | Maximum working pressure

Code	Pressure, MPa	Note
02	1.6
04	4	by default: flange, min. class 4 MPa
06	6.3
10	10
16	16
20	20
25	25
30	30
35	35
40	40
45	45
70	70
90	90
XX	Special	description required

5E | Process connection

Code	Standard	Note
RXXXYYYZ	GOST 33259	XXX-DN, mm; YYY-PN, kgf/cm²; Z-version
ENXXXYYYZ	EN 1092-1	XXX-DN, mm; YYY-PN, bar; Z-version
ASXXYYYYZZZ	ASME B16.5	XX-DN, inch; YYYY-Class; ZZZ-version
FR	HG/T 20592-2009 WN RF PN16	DN10–DN300
FQ	HG/T 20592-2009 WN RF PN25	DN10–DN300
FT	HG/T 20592-2009 WN RF PN40	DN10–DN300
FU	HG/T 20592-2009 WN RF PN63	DN10–DN300
FV	HG/T 20592-2009 WN RF PN100	DN10–DN300
FW	HG/T 20592-2009 WN RF PN160	DN10–DN300
FA	HG/T 20615-2009 WN RF Class150	DN15–DN300
FB	HG/T 20615-2009 WN RF Class300	DN15–DN300
FC	HG/T 20615-2009 WN RF Class600	DN15–DN300
FD	HG/T 20615-2009 WN RF Class900	DN15–DN300
FE	HG/T 20615-2009 WN RF Class1500	DN15–DN300
GS	G thread	pipe thread
G4	G1/4" thread	pipe thread
G2	G1/2" thread	pipe thread
G1	G1" thread	pipe thread
DS	DIN 11851-SI	mm
DT	DIN 11851-US	inches
DU	DIN 11864-1 Form A, threaded	sanitary
DV	DIN 11864-2 Form A, flat flange
GT	GB/T 9115-2010 RF PN25	DN10–DN300
GU	GB/T 9115-2010 RF PN16	DN10–DN300
GV	GB/T 9115-2010 RF PN40	DN10–DN300
GW	GB/T 9115-2010 RF PN63	DN10–DN300
GX	GB/T 9115-2010 RF PN100	DN10–DN300
GY	GB/T 9115-2010 RF PN160	DN10–DN300
US	UNF thread	tapered
UA	UNF thread 9/16-18UNF	tapered
UB	UNF thread 1 3/8-12UNF	tapered
RC	RC thread
RD	Rc 3/4" thread
HS	Tri-clamp DN32676:2022-10	∅25
HA	Tri-clamp DN32676:2022-10	∅34
HB	Tri-clamp DN32676:2022-10	∅50.5
HC	Tri-clamp DN32676:2022-10	∅64
HD	Tri-clamp DN32676:2022-10	∅91
AS	ASME B16.5-2020, weld-neck Class 150	1/2–12"
AT	ASME B16.5-2020 Class 300	1/2–12"
AU	ASME B16.5-2020 Class 600	1/2–12"
AV	ASME B16.5-2020 Class 900	1/2–12"
AW	ASME B16.5-2020 Class 1500	1/2–12"
AX	ASME B16.5-2020 Class 2500	1/2–12"
GA	GOST 12821-80, 1.6 MPa	DN10–DN300
GB	GOST 12821-80, 2.5 MPa	DN10–DN300
GC	GOST 12821-80, 4 MPa	DN10–DN300
GD	GOST 12821-80, 6.3 MPa	DN10–DN300
GE	GOST 12821-80, 10 MPa	DN10–DN300
GF	GOST 12821-80, 16 MPa	DN15–DN300
GG	GOST 12821-80, 20 MPa	DN15–DN300
GH	GOST 33259-2015 PN16-B	DN15–DN300
GJ	GOST 33259-2015 PN25-B	DN15–DN300
GK	GOST 33259-2015 PN40-B	DN15–DN300
GL	GOST 33259-2015 PN63-B	DN15–DN300
GM	GOST 33259-2015 PN100-B	DN15–DN300
GN	GOST 33259-2015 PN160-B	DN15–DN300
ES	EN 1092-1:2007(E) Type11 PN16	DN10–DN300
ET	EN 1092-1:2007(E) Type11 PN25	DN10–DN300
EU	EN 1092-1:2007(E) Type11 PN40	DN10–DN300
EV	EN 1092-1:2007(E) Type11 PN63	DN10–DN300
EW	EN 1092-1:2007(E) Type11 PN100	DN10–DN300
EX	EN 1092-1:2007(E) Type11 PN160	DN10–DN300
JS	JIS B2220:2004 RF 10K	DN10–DN300
JT	JIS B2220:2004 RF 20K	DN10–DN300
JU	JIS B2220:2004 RF 40K	DN10–DN300
JV	JIS B2220:2004 RF 63K	DN10–DN300
SS	SMS 1145, threaded	sanitary
MS	Metal seal
OS	O-Ring seal
ZS	ZG1/8-F
ZT	ZG1/2-F
ZU	ZG3/4-F
ZV	ZG1-F
NR	1/4" NPT-F
NS	1/2" NPT-F
NT	3/4" NPT-F
NU	1" NPT-F
BS	1/2" flange
VS	VCO connection
VA	VCO connection	VCO1/2"
VB	VCO connection	VCO3/4"
VC	VCO connection	VCO1"
VR	VCR connection	VCR1/8"
VT	VCR connection	VCR1/4"
VU	VCR connection	VCR1/2"
VV	VCR connection	VCR3/4"
VW	VCR connection	VCR1"
KT	Union nut (cartridge connection)
C8	Process connection type change only	description required: only the flange or thread changes; the sensor body remains unchanged
C9	Special connection	description required

6F | Measuring tube material

Code	Material	Note
S	316L	default
G	316L with high nickel content
L	904L
T	Titanium
C	C4 steel
H	Hastelloy
D	Duplex steel
A	Tantalum
X	Other materials	description required

7G | Accuracy

Code	Description	Note
S	0.1%	mass
A	0.15%	mass
B	0.2%	mass
C	0.5%	mass
D	1.0%	mass
X	Other requirements	description required

8H | Transmitter mounting type

Code	Description	Note
N	Integrated design
S	Remote (separate) design	default cable length — 3 m
J	Compact integrated design	without explosion protection
D	DIN-rail mounting	without explosion protection
X	Other requirements	detailed description required

9I | Display

Code	Description	Note
C	With display
M	Without display	default
X	Other requirements	description required

10J | Output signals

Code	Description	Note
M	Modbus RTU/RS-485, active pulse	default
L	4-20 mA active + default signals
H	HART + 4-20 mA active + default signals
P	Modbus RTU/RS-485, active pulse	in addition to the main signals (code "P" = "+ Modbus…" per the operation manual)
X	Other requirements	description required

Output set per the type approval description: 4–20 mA (incl. HART), frequency-pulse 0–10,000 Hz, RS-485 (Modbus RTU), CAN; PROFIBUS PA is an option; availability depends on the version (type approval description, block 10J).

11K | Certification

Code	Description	Note
N	None	default
C	Ex explosion protection
A	Design to 3-A requirements
S	TS special equipment manufacturing license
J	CCS classification society certificate
X	Other requirements	description required

12L | Transmitter version

Code	Version	Note
V1	ME100	default
V2	ME200
V3	ME300
V4	ME400	ultra-compact, stainless steel, without display
XX	Special version	description required

13M | Measurement mode

Code	Mode	Note
M	Mass	default
D	Density
A	Mass and density
X	Other requirements	description required

14N | Process connection material

Code	Material	Note
E	304
S	316L	default
G	316L with high nickel content
L	904L
T	Titanium
C	C4 steel
H	Hastelloy
D	Duplex steel
A	Tantalum
X	Other materials	description required

15O | Sensor housing material

Code	Material	Note
E	304
S	316L
X	Other materials	description required

16P | Power supply

Code	Power	Note
1	24 V DC	default
2	220 V AC / 24 V DC	automatic
X	Other requirements	description required

17Q | Cable entry

Code	Type	Note
N	1/2" NPT
M	M20×1.5	default
X	Special version	description required

18R | Density measurement

Code	Accuracy, kg/m³	Note
1	3
2	1
3	0.5
4	0.2
5	0.15
Q	No requirements	default

19S | Isothermal jacket

Code	Description	Note
N	None	default
Y	Yes	(learn more)

20T | Interface language

Code	Language	Note
E	English
C	Chinese
R	Russian	default
X	Other	description required

21U | Additional scope of supply

Code	Description	Note
0	None	default
1	Mating carbon steel flanges, fasteners, spiral-wound gaskets
2	Mating stainless steel flanges, fasteners, spiral-wound gaskets
X	Other	description required

22V | Additional ETO options — on request

Code	Description
N	None	default
ETOZZZ	ZZZ — alphanumeric designation. May not be shown on the nameplate; it is linked to the serial number. Used for custom solutions tailored to unique requirements through engineering and design work.

23X | Warranty terms

Code	Description	Note
-	Standard: 18 months from the delivery date or 12 months after installation — whichever comes first (operation manual, clause 5.3)	default
EW	Extended: 24 months from commissioning, but not more than 36 months from the date of manufacture
SW	Special — specific warranty terms. Specified separately